++ Installation Guide of Braille EDGE Display Driver for JAWS

2011-05-25
HIMS International Corporation.


--


Please be sure that this driver is compatible with JAWS 10 or higher version so earlier than JAWS 10 may not work correctly.

Here are default key descriptions for the Braille EDGE using Braille Keyboard.
 DOC type: www.himsintl.com/upload/JAWS/Hot-Key_Define_Jaws_BrailleEDGE.doc.
 TXT type: www.himsintl.com/upload/JAWS/Hot-Key_Define_Jaws_BrailleEDGE.txt.

This document is consisted of guides for installation/deletion, USB connection and Bluetooth connection.


--

 
++ HOW TO INSTALL Braille EDGE Display Driver.

1. Download Installer from the below link to your PC.
 www.himsintl.com/upload/JAWS/HIMS_Braille_Driver_For_Jaws_V2_0.zip.
 Please be sure that the zip file size is exactly 5,162,086 bytes (almost 4.92 MB).
2. Unzip the downloaded zip file on your PC.
3. Run the installer program and installation wizard will be started.
 - To start installation, clink ¡°Install¡± bottom.
 - This time, if you haven¡¯t installed the JAWS yet, the installer will warn you with the message ¡°JAWS is not existed¡± and you can¡¯t advance installation any more.
4. Once the installer completely installed necessary files for JAWS, ¡°Device Driver Installation Wizard¡± will be appeared. It is the USB driver to make connection between Braille EDGE and JAWS via USB cable.
 - To start installation, click ¡°next¡± button.
 - Select ¡°HIMS USB¡± in the list box and click ¡°finish¡± button
 - Now all process of installation have been done.
 - To finish installation, click ¡°finish¡± button.
 
++ HOW TO MAKE USB Connection using USB cable.

1. Once you have installed the Braille EDGE Display driver for JAWS, Connect the USB OTG cable into the USB OTG port on the Braille EDGE and the wider end of the cable should be connected into USB port on your computer.
2. Run ¡°Terminal for the Screen Reader.
3. You will see the ¡°New Hardware Wizard¡± on your PC.
4. Choose ¡°Yes, this time only¡± and then press ¡°Next¡± button.
5. Select ¡°Install the software automatically¡± and then press ¡°Next¡± button.
6. You will see the next screen and then press ¡°Next¡± button.
7. Press ¡®finish¡¯ button then installation will be completed.
 - For the next time when you connect the Braille EDGE to PC, there is no need to install or register the USB driver.
8. Run JAWS and select ¡°Braille¡± under the ¡°File¡± menu in the JAWS.
9. Select ¡°Braille EDGE¡± as a ¡°Default Braille Display¡± and ¡°USB¡± as a port.
 - That¡¯s all that you can connect the Braille EDGE to JAWS via USB cable.
 
++ HOW TO MAKE Bluetooth Serial Connection

1. Click ¡°Add¡± button in Bluetooth Dialog in XP SP2.
2. Check ¡°My device is set up and ready to be found¡± checkbox in order for other Bluetooth device to find your PC.
3. Searching the Bluetooth devices nearby your PC.
4. Select the ¡°BrailleEDGEXXXX¡± that you want to connect to.
5. Enter the PINCODE to trust between two devices and then click ¡°next¡± button.
 - At this time, the Braille EDGE will require PINCODE against your PC.
 - Trusting between two devices.
 - Complete trusting between two devices.
 - Your PC will make the virtual Bluetooth serial port automatically.
 - Please make sure that the Bluetooth serial port are made correctly.(outgoing port: COM20).
 - It is possible that the port is different from example per each PC.
6. Run ¡°Terminal for the Screen Reader¡±.
7. Please make sure that the message is ¡°terminal mode¡±.
8. Run JAWS and select ¡°Braille¡± under the ¡°File¡± menu in the JAWS.
9. Select ¡°Braille EDGE¡± as a ¡°Default Braille Display¡± and ¡°USB¡± as a port.
10. Select ¡°Braille EDGE¡± as ¡°Default Braille Display¡± and ¡°COM20¡± as ¡°Select the output port¡±.
 - That¡¯s all that you can connect the Braille EDGE to JAWS via Bluetooth Serial Port.
 
 
++ HOW TO REMOVE Braille EDGE Display driver

1. Move to the folder where the JAWS was installed.
 - For example of that you installed it in ¡°C:\Program Files\Freedom Scientific¡±.
2. Move to ¡°\Shared\Drivers\Braille\1.0\ThirdParty\brlsense¡± from the folder.
3. Run ¡°Uninstaller.exe¡±
4. When running the JAWS, following message will be displayed.
 - ¡®In order to complete the uninstallation action, you must reboot the computer. If you do not want to reboot the computer now, the uninstallation will be complete when you reboot the computer.¡¯
5. If not running the JAWS, the folder will be deleted automatically.


--


If you have any questions, please call Justin in Tech Support at +82-42-864-4601(ext. 100) or e-mail to supports@himsintl.com.

HIMS International Corporation.
139-9, Gajung-dong, Yuseong-gu, Daejeon, KOREA, 305-350 
Phone: +82-42-864-4601(ext. 607)
www.himsintl.com